# Slow response to smartctl command (linux)

**URL:** <https://forum.storj.io/t/slow-response-to-smartctl-command-linux/27775>\
**Category:** troubleshooting\
**Tags:** hardware\
**Created:** [September 6, 2024, 11:11am UTC](https://forum.storj.io/t/slow-response-to-smartctl-command-linux/27775 "2024-09-06T11:11:05Z")\
**Posts on this page:** 5\
**Page:** 1

<div class="post-metadata">

**Author:** ![andrew2.hart](https://storj.bcdn.literatehosting.com/user_avatar/forum.storj.io/andrew2.hart/32/6415_2.png) [@andrew2.hart](https://forum.storj.io/u/andrew2.hart)\
**Post date:** [September 6, 2024, 11:11am UTC](https://forum.storj.io/t/slow-response-to-smartctl-command-linux/27775/1 "2024-09-06T11:11:05Z")

</div>

Hello fellow hard disk enthusiasts! I am having some trouble with a hard drive that just seems a bit sluggish and slow compared to “normal”.  
The most obvious symptom is that when I check the SMART health, the smartctl -a /dev/sdq command takes forever (maybe 30 seconds or more) to display. It says SMART Health Status: OK.  
Other than that it just shows a tiny bit more utilized than other disks.  
Any ideas what could cause this?

---

<div class="post-metadata">

**Author:** ![EasyRhino](https://storj.bcdn.literatehosting.com/user_avatar/forum.storj.io/easyrhino/32/1133_2.png) [@EasyRhino](https://forum.storj.io/u/EasyRhino)\
**Post date:** [September 6, 2024, 3:54pm UTC](https://forum.storj.io/t/slow-response-to-smartctl-command-linux/27775/2 "2024-09-06T15:54:21Z")

</div>

it’s silly but maybe a cabling problem.

---

<div class="post-metadata">

**Author:** ![Alexey](https://storj.bcdn.literatehosting.com/user_avatar/forum.storj.io/alexey/32/41_2.png) [@Alexey](https://forum.storj.io/u/Alexey)\
**Post date:** [September 7, 2024, 3:27am UTC](https://forum.storj.io/t/slow-response-to-smartctl-command-linux/27775/3 "2024-09-07T03:27:07Z")

</div>

I would agree with @EasyRhino, please try to disconnect the cable from the controller and from the disk, remove dust and reconnect again. If it wouldn’t help, please try to replace the cable.

---

<div class="post-metadata">

**Author:** ![andrew2.hart](https://storj.bcdn.literatehosting.com/user_avatar/forum.storj.io/andrew2.hart/32/6415_2.png) [@andrew2.hart](https://forum.storj.io/u/andrew2.hart)\
**Post date:** [September 7, 2024, 6:18am UTC](https://forum.storj.io/t/slow-response-to-smartctl-command-linux/27775/4 "2024-09-07T06:18:13Z")

</div>

It is a good idea but it is one of those caddy/backplane types. So no cable.  
Maybe there is a problem with the connectors…  
I wonder why data transfers fine but just the smartctl command is badly affected though

---

<div class="post-metadata">

**Author:** ![Alexey](https://storj.bcdn.literatehosting.com/user_avatar/forum.storj.io/alexey/32/41_2.png) [@Alexey](https://forum.storj.io/u/Alexey)\
**Post date:** [September 7, 2024, 7:11am UTC](https://forum.storj.io/t/slow-response-to-smartctl-command-linux/27775/5 "2024-09-07T07:11:19Z")

</div>

Perhaps the firmware is not so fast or the specialized microcontroller on the circuit board. Not all disks are equal.
